?WikiName? - Souls Modding Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== JigglerBaseParam ======
===== Fields =====
^ Field ^ Type ^ Offset ^ Description ^ Notes ^
| ctrlType | ''u8'' | ''0x0'' | The setup type used for setting up the jiggler. | This field uses the following enum: JIGGLER_CTRL_TYPE |
| calcType | ''u8'' | ''0x1'' | The calculation type to use with the jiggler. | This field uses the following enum: JIGGLER_CALC_TYPE |
| reserved1 | ''dummy8'' | ''0x2'' |  | This field is padding. |
| dmyPolyId | ''u32'' | ''0x4'' | The dummy polygon ID to apply the jiggler to. Only valid if the control type is set to Dummy Polygon. |  |
| strCtrlBoneName | ''fixstr'' | ''0x8'' | The bone name to apply the jiggler to. Only valid if the control type is set to Skeleton. |  |
| reserved2 | ''dummy8'' | ''0x20'' |  | This field is padding. |
| axisX | ''u8'' | ''0x28'' | The axis to treat as the X-axis (so that it does not overlap with other axes). | This field uses the following enum: IK_KNEE_AXIS_TYPE |
| axisY | ''u8'' | ''0x29'' | The axis to treat as the Y-axis (so that it does not overlap with other axes). | This field uses the following enum: IK_KNEE_AXIS_TYPE |
| axisZ | ''u8'' | ''0x2a'' | The axis to treat as the Z-axis (so that it does not overlap with other axes). | This field uses the following enum: IK_KNEE_AXIS_TYPE |
| bUseFollowBaseBone | ''u8'' | ''0x2b'' | If ON, the jiggler will follow the root bone. | This field is a boolean. |
| limitAngleDeg_MinX | ''s8'' | ''0x2c'' | The minimum angle for the X-axis. In degrees. |  |
| limitAngleDeg_MaxX | ''s8'' | ''0x2d'' | The maximum angle for the X-axis. In degrees. |  |
| limitAngleDeg_MinY | ''s8'' | ''0x2e'' | The minimum angle for the Y-axis. In degrees. |  |
| limitAngleDeg_MaxY | ''s8'' | ''0x2f'' | The maximum angle for the Y-axis. In degrees. |  |
| behaviorParamId | ''u32'' | ''0x30'' | The rotation behavior parameter to use. | This field refers to the following params: [[ac6-refmat:param:JigglerBehaviorParam]] |
| behaviorSlideParamId | ''u32'' | ''0x34'' | The movement behavior parameter to use. | This field refers to the following params: [[ac6-refmat:param:JigglerBehaviorSlideParam]] |
| limitOffset_MinX | ''f32'' | ''0x38'' | The minimum position offset for the X-axis. |  |
| limitOffset_MaxX | ''f32'' | ''0x3c'' | The maximum position offset for the X-axis. |  |
| limitOffset_MinY | ''f32'' | ''0x40'' | The minimum position offset for the Y-axis. |  |
| limitOffset_MaxY | ''f32'' | ''0x44'' | The maximum position offset for the Y-axis. |  |
| limitOffset_MinZ | ''f32'' | ''0x48'' | The minimum position offset for the Z-axis. |  |
| limitOffset_MaxZ | ''f32'' | ''0x4c'' | The maximum position offset for the Z-axis. |  |
| behaviorWorldFixParamId | ''u32'' | ''0x50'' | The parameter ID to use when the jiggler is attached to the ground. | This field refers to the following params: [[ac6-refmat:param:JigglerBehaviorWorldFixParam]] |
| behaviorTargetBoneRateParamId | ''u32'' | ''0x54'' | The parameter ID to use for determining the percentage rate from a specified joint. | This field refers to the following params: [[ac6-refmat:param:JigglerBehaviorTargetBoneRateParam]] |
| pad | ''dummy8'' | ''0x58'' |  |  |
| followBaseBone_SpineFollowRateRot | ''f32'' | ''0x68'' | Used if Follow Root Bone is ON. The tracking rate to the new position after the rotation of the root bone for the spine. |  |
| followBaseBone_SpineFollowRatePos | ''f32'' | ''0x6c'' | Used if Follow Root Bone is ON. The tracking rate to the new position after the movement of the root bone for the spine. |  |
| followBaseBone_OffsetX | ''f32'' | ''0x70'' | Used if Follow Root Bone is ON. The follow position offset on the X-axis for the spine when movement of the root bone occurs. |  |
| followBaseBone_OffsetY | ''f32'' | ''0x74'' | Used if Follow Root Bone is ON. The follow position offset on the Y-axis for the spine when movement of the root bone occurs. |  |
| followBaseBone_OffsetZ | ''f32'' | ''0x78'' | Used if Follow Root Bone is ON. The follow position offset on the Z-axis for the spine when movement of the root bone occurs. |  |
| reserved4 | ''dummy8'' | ''0x7c'' |  | This field is padding. |



===== Enums =====


==== JIGGLER_CTRL_TYPE ====
^ Option ^ Description ^ Notes ^
| ''0'' | Dummy Polygon | |
| ''1'' | Skeleton | |


==== JIGGLER_CALC_TYPE ====
^ Option ^ Description ^ Notes ^
| ''0'' | Position only | |
| ''1'' | Rotation only | |
| ''2'' | Position -> Rotation | |
| ''4'' | Fixed to World | |
| ''5'' | Percentage from Specified Joint | |


==== IK_KNEE_AXIS_TYPE ====
^ Option ^ Description ^ Notes ^
| ''0'' | + X | |
| ''1'' | + Y | |
| ''2'' | + Z | |
| ''3'' | - X | |
| ''4'' | - Y | |
| ''5'' | - Z | |
?WikiName? - Souls Modding Wiki

User Tools

Site Tools

Page Tools
